ProductsMotor & Control Solutions

A selection of our standard platforms. Custom motor matching, firmware features and mechanical form factors are available on request.

Brushless Motors

Inner-rotor BLDC motors matched to our controllers: 24 V and 40 V battery platforms, 350-1600 W.

24V brushless drill motor

24 V Brushless Drill Motor

6-slot / 4-pole inner-rotor motor, 350 W, 29,500 rpm, 0.12 N·m, N35SH magnets, for 30 N·m-class cordless drills.

40V brushless brush cutter motor

40 V Brushless Brush Cutter Motor

12-slot / 10-pole inner-rotor motor, 1,600 W, 10,650 rpm, 1.468 N·m, 82.7% peak efficiency, N45SH magnets.

20V brushless chainsaw motor

20 V Brushless Chainsaw Motor

6-slot / 4-pole inner-rotor motor, 350 W, 25,000 rpm, 0.12 N·m, N38H magnets.

Vector Controllers

FOC controllers for pumps, spindles and industrial drives, with MODBUS/485, potentiometer or hall interfaces.

PUMP100 FOC controller

PUMP100 48 V Fluid Pump FOC Controller

48 V / 20 A, 1000 W, 50 A peak phase current, MODBUS control, constant speed, fault and runtime logging, 0.95 efficiency.

LD001 radar spindle controller

LD001 Radar Spindle BLDC Controller

24–48 V / 40 A, 500–1500 W, 60 A peak phase current, hall-based control, potentiometer speed setting, direction control and 485 communication.

3.6kW water drill controller

3.6 kW Field-Weakening Water Drill Controller

Single-phase 220 V AC, active PFC with 0.99 power factor, field-weakening electronic speed control, compatible with 20–500 mm drill bits.

High-Voltage Controllers

Controllers for 85-270 V AC and 380 V three-phase tools: water drills, cutters, compressors, fans and impact tools.

380V air compressor controller

380 V Three-Phase Air Compressor Controller

380 VAC ±10%, 2000 W, sensorless FOC with three-shunt sensing, IPM power stage and bridgeless PFC, 485 with 1-master / 7-slave addressing.

220V air compressor controller

220 V Air Compressor Controller

Single-phase 220 V AC, active PFC with 0.99 power factor, sensorless control, dual-cylinder master/slave operation, pressure detection and EMC tested.

9500 water drill controller

9500 AC Series-Wound Water Drill Controller

85–270 V AC, 15–25 A, 3000–5000 W, 48 A current limit, constant speed, load indication, temperature and stall protection.

YYFAN high voltage fan controller

YYFAN High-Voltage Fan Controller

Single-shunt sensorless FOC, 85–270 V AC, 2–6 A, 200–600 W, 10 A peak phase current, stepless speed and constant-speed operation.

220V AC nailer controller

220 V AC Nailer Controller

Single-phase 220 V AC controller for corded nailers; constant speed, current limiting and stall protection.

220V high pressure core drill controller

220 V High-Pressure Core Drill Controller

Single-phase 220 V AC FOC controller for core drills, with soft start, constant speed and over-current protection.

86230 multi-tool controller

86230 AC Series-Wound Multi-Tool Controller

85–270 V AC / 50–60 Hz, 300–600 W, 8 A limit, stepless and multi-step speed, constant speed, stall protection, 0.98 efficiency.

Lithium Power Tools

Controllers for 20 V / 40 V / 80 V battery platforms: drills, drivers, wrenches, grinders, saws and washers.

20V brushless drill controller

20 V Brushless Drill Controller

20 V 5-cell battery pack, forward/reverse, brake, 3-LED state of charge, over-voltage / under-voltage / over-current / stall / phase-loss protection, soft start ≤200 ms.

40V/80V cut-off saw controller

40 V/80 V Dual-Pack Cut-Off Saw Controller

4000 W on 40 V or 80 V platforms, FOC, potentiometer speed setting, constant speed, field weakening, anti-spark and custom display support.

20V trimmer controller

20 V Brushless Trimmer Controller

Soft start, 10 s delayed light, three-stage over-current protection, short circuit, stall, low-voltage and temperature protection; PCB 51.5×76.5 mm.

20V impact driver controller

20V Impact Driver Controller

20V brushless impact driver controller with three-stage current limiting, stall and temperature protection.

20V rotary hammer controller

20V Rotary Hammer Controller

20V brushless rotary hammer controller, soft start and constant speed, three-stage over-current, temperature and stall protection.

20V miter saw controller

20V Miter Saw Controller

20V lithium miter saw controller with constant speed, current limiting and soft start for accurate cuts.

20V washer controller

20V Brushless Washer Controller

Portable washer controller with brushless drive, low-voltage cut-off and over-current protection.

20V electric jack controller

20V Electric Jack Controller

Electric jack controller with current limiting, stall protection and remote switch input.

Garden Tools

Controllers for chainsaws, brush cutters, pruners and hedge trimmers, with constant-speed and protection features.

36V brush cutter controller

36 V Rear Brush Cutter Controller

Three constant speeds (4,850 / 6,650 / 8,150 rpm), battery and gear display, phase current limit, three-stage over-current, stall and temperature protection.

20V pruner platform controller

20 V Pruner Platform Controller

Half-open / full-open modes with lock, LED state of charge and buzzer, over-voltage, under-voltage, over-discharge, three-stage over-current, short circuit and stall protection.

30-48V chainsaw controller

30–48 V Chainsaw Controller

30–48 V, 60 A, 1500–3500 W, multi-step speed, constant speed, current and power limiting, double switch protection.

High-Voltage, No Electrolytic Capacitor

Electrolytic-free power stages for high-voltage tools, using single-shunt FOC to shrink bus capacitance.

4500W electrolytic-free water drill controller

4500 W Electrolytic-Free Water Drill Controller

Single-phase 220 V AC, three-shunt sensorless FOC with no electrolytic bus capacitor, for high-power water drills; protection and display interfaces included.

3000W electrolytic-free wall chaser controller

3000 W 230 V Brushless Wall Chaser Controller (No Cap)

230 V AC input, electrolytic-free power stage, IPM drive; designed for wall chasers and cut-off machines.

700W drill press controller

700 W 220 V Drill Press Controller (No Cap)

220 V AC, electrolytic-free design with keypad and digital display, sensorless FOC speed control.

2000W direct-drive polisher controller

2000 W Direct-Drive Polisher Controller (No Cap)

Direct-drive polisher controller sharing the electrolytic-free 230 V platform; smooth start and constant speed.

8001 polisher controller

8001 High-Voltage Polisher Controller (No Electrolytic Capacitor)

Single-phase 220 V AC, electrolytic-free design with 0.85 power factor, independent display with electronic speed control, 20–500 mm bit compatibility.

Other Products

Display boards and control boards developed alongside the controller platforms.

TFT display board

2.0" TFT Display Board

240×320 TFT with ST7789T3 driver, UART link to the main controller, shows voltage, power, runtime and three-level load ratio, hall speed sensing and English/Chinese UI.

Need a variant of any platform?
Tell us voltage, power, tool type and target cost.
Contact Us